Cold Rolled Steel Sheet & Coil (CR)
품질 사양(Quality Specifications)
Classification |
KSD 3512 | JIS G3141 | ASTM A1008 | EN10130 |
---|---|---|---|---|
CQ (Commercial Quality) |
SPCC | SPCC | CS | DC01(Fe P01) |
DQ (Drawing Quality) |
SPCD | SPCD | DS | DC03(Fe P03) |
DDQ (Deep Drawing Quality) |
SPCE | SPCE | DDS | DC04(Fe P04) |
DDQ-N (StabilizedDeep Drawing Quality) |
SPCEN | SPCEN | DDS | DC04(Fe P04) |
EDDQ |
EDDS | DC05Fe P05) |
제품 분류(Classification of Products)
Commercial
이 품질의 상업용 시트는 단순 굽힘 또는 중간 성형 용입니다. 상업용 강판은 실온에서 어떤 방향 으로든 자체적으로 평평하게 구부릴 수 있습니다. 자동차 패널, 가전 제품, 드럼, 파이프, 농기구, 사무용품, 건축 및 토목 자재 등 다양한 용도로 사용되며 다양한 코팅 용 비금속으로 사용됩니다.
Sheet of thisquality is for simple bending or moderate forming. Commercial steel sheet can be bent flat uponitself in any direction at room temperature. Ithas a wide variety of uses, including automotivepanels, electrical home appliances, drums, pipes,farm implements, office supplies, building andcivil work materials, and as base metal forvarious coatings.
Drawing
이 품질의 도면 시트는 강철의 생산, 선택 및 용융에서 더 높은 표준으로 인해 상업용 강철보다 더 높은 수준의 연성을 가지며 성능이 더 일관됩니다. 자동차 패널, 시청각 장비 및 난방 장치에 적합합니다.
Sheetof this quality has a greater degree of ductilityand is more consistent in performance thancommercial steel because of higher standards inproduction, selection and melting of the steel. Itis suitable for automotive panels, audio-visualequipment, and heating apparatuses.
DeepDrawing
이 지정의 딥 드로잉 시트는 드로잉 강재가 엄격한 드로잉 요구 사항을 가진 부품의 제조에 충분한 연성을 제공하지 못하거나 시트가 노화되지 않아야하는 응용 분야에 충분한 정도의 연성을 제공하지 않을 때 사용해야합니다. 이 품질은 특수 제강 및 마무리 작업을 통해 생산됩니다. 자동차 전면 패널 및 후면 펜더에 적합합니다.
Sheet of this designation should beused when drawing steel will not provide asufficient degree of ductility for fabrication ofparts with stringent drawing requirements, orapplications that require the sheet be free fromaging. This quality is produced through specialsteelmaking and finishing practices. It issuitable for automotive front panels and rearfenders.
Stabilized Deep Drawing
품질의 제품은 작업 성 측면에서 최고의 품질을 자랑합니다. Front Fender 나 Wire 등 복잡한 처리가 필요한 자동차 부품에 적합합니다. Al-killed로 만든 Non-aging Deep Drawing Sheet로 극심한 신축이나 변형에 대한 품질이 보장됩니다.
Stabilized deep drawing qualityproducts boast the highest quality in terms ofworkability. It is suitable for automotive partsthat require complicated treatment such as frontfenders or wire. As a non-aging deep drawing sheetmade with Al-killed, quality is guaranteed againstextreme stretching or straining.
Surface Finish
조도 냉간 압연 강판의 표면 조도는 둔하거나 밝다.
The surface finish of cold-rolledsteel sheet is either dull or bright.
Dull Finish
강철 표면에 수많은 미세 입자를 부착하여 얻을 수있는 칙칙한 마감은 종종 '배 피부 마감'또는 '달걀 껍질 질감'이라고합니다. 곡물은 강철 그릿 블라스트 롤로 만들어집니다. 무딘 마감은 윤활유가 전체 표면에 고르게 퍼져 마찰 가능성을 줄이므로 드로잉에 유용합니다.
Dull finish, which is attained byattaching numerous fine grains onto the steelsurface, is often called 'pear-skin finish' or'egg-shell texture'. The grains are made by steelgrit blasted roll. The dull finish is usefulin drawing because lubricant oil can be evenlyspread over the entire surface, thereby reducingthe possibility of friction. The fine grainsalso help boost paint adherence and extend thesteel life span of the steel.
BrightFinish
밝은 마감은 장식용으로 최적 인 고품질 거칠기를 제공합니다. 시트 표면은 미세한 광택 롤로 감겨 있습니다.
Bright finish presents high-qualityroughness that is optimal for decorative purposes.The sheet surface is rolled with fine polishedrolls.
Edges
Classification |
Specifications |
---|---|
Mill Edge | Edges produced by trimming hot rolled coil during the pickling process, prior to cold rolling. |
Slit Edge (Trimmed Edge) |
Edges produced by shearing or slitting during the cold rolling process. |
Oiling
밝은 마감은 장식용으로 최적 인 고품질 거칠기를 제공합니다. 시트 표면은 미세한 광택 롤로 감겨 있습니다.
Sheet that isprocessed with the final step being theapplication of oil to the surface; usuallyintended to provide protection from rusting duringshipment and storage. The oil may also serve toassist in the subsequent fabrication process, butthis is not usually the main purpose. Dongbu Steeldelivers its steel products either oiled (heavy,general or light, dos oiling, powdering) orun-oiled.
화학 성분(Chemical Components)
Standard Specification |
Applications |
Chemical Component |
|||||
---|---|---|---|---|---|---|---|
C |
Si |
Mn |
P |
S |
|||
KS D 3512 (JIS G 3141) |
SPCC | CQ | ≤ 0.12 | - | ≤ 0.50 | ≤ 0.040 | ≤ 0.045 |
SPCD | DQ | ≤ 0.10 | - | ≤ 0.45 | ≤ 0.035 | ≤ 0.035 | |
SPCE (N) | DDQ (Non-Aging) | ≤ 0.08 | - | ≤ 0.40 | ≤ 0.030 | ≤ 0.030 | |
ASTM A 1008 | CS | CQ | ≤ 0.10 | - | ≤ 0.60 | ≤ 0.030 | ≤ 0.035 |
DS | DQ | ≤ 0.08 | - | ≤ 0.50 | ≤ 0.020 | ≤ 0.030 | |
DDS | DDQ (Non-Aging) | ≤ 0.06 | - | ≤ 0.50 | ≤ 0.020 | ≤ 0.025 | |
EN 10130 | DC01 (Fe P01) | CQ | ≤ 0.12 | - | ≤ 0.60 | ≤ 0.045 | ≤ 0.045 |
DC03 (Fe P03) | DQ | ≤ 0.10 | - | ≤ 0.45 | ≤ 0.035 | ≤ 0.035 | |
DC04 (Fe P04) | DDQ (Non-Aging) | ≤ 0.08 | - | ≤ 0.40 | ≤ 0.030 | ≤ 0.030 | |
DC05 (Fe P05) | EDDQ | ≤ 0.06 | - | ≤ 0.35 | ≤ 0.025 | ≤ 0.025 |
기계적 성질(Mechanical Properties)
Standard Specification |
Application |
Mechanical Property |
||||||||
---|---|---|---|---|---|---|---|---|---|---|
Y.P |
T.S |
Elongation Min (%) |
||||||||
Yielding Point (N/㎟) | Tensile Strength (N/㎟) |
0.25≤t <0.40 |
0.40≤t <0.60 |
0.60≤t <1.0 |
1.0≤t <1.6 |
1.6≤t <2.5 |
t≥2.5 | |||
KS D 3512 (JIS G 3141) |
SPCC | CQ | - | ≥270 | (32) | (34) | (36) | (37) | (38) | (39) |
SPCD | DQ | - | ≥270 | 34 | 36 | 38 | 39 | 40 | 41 | |
SPCE (N) | DDQ (Non-Aging) | - | ≥270 | 36 | 38 | 40 | 41 | 42 | 43 | |
ASTM A 1008 | CS | CQ | (140~275) | - | 30 (L0 =50mm) | |||||
DS | DQ | (150~240) | - | 36 (L0 =50mm) | ||||||
DDS | DDQ (Non-Aging) | (115~200) | - | 38 (L0 =50mm) | ||||||
EDDS | EDDQ | (105~170) | - | 40 (L0 =50mm) | ||||||
EN 10130 | DC01 (Fe P01) | CQ | ≤ 280 | 270~410 | 28 (L0 =80mm) | |||||
DC03 (Fe P03) | DQ | ≤ 240 | 270~410 | 34 (L0 =80mm) | ||||||
DC04 (Fe P04) | DDQ (Non-Aging) | ≤ 210 | 270~410 | 38 (L0 =80mm) | ||||||
DC05 (Fe P05) | EDDQ | ≤ 180 | 270~410 | 40 (L0 =80mm) |
Standard Specification |
Mechanical Property |
||
---|---|---|---|
Hardness |
|||
Temper |
HRB |
Hv |
|
KS D 3512 (JIS G 3141) |
1/8H | 50~71 | 95~130 |
1/4H | 65~80 | 115~150 | |
1/2H | 74~89 | 135~185 | |
H |
≥85 | ≥170 |